Tuesday, January 1, 2013

Belite Aluminum Ultralight Aircraft Cabin Construction, #6

Please note: James' blog has moved to a Wordpress site. To access it, please visit http://jameswiebe.wordpress.com/. All posts have been transferred to the new site, and all new posts will only be accessible via Wordpress. Thank you for your interest!


#6 in the series.

We will start by attaching the rear fuselage attachment gussets.  There are six:  two on each side, and two on the bottom.  The top side gussets, the bottom side gussets, and the bottom gussets are each unique.  They may vary slightly from these photos in appearance, due to fit and lightening improvements.  Fit, cleco, and rivet them in place, as shown in the following photos:

Bottom Side Gusset and Bottom Gusset, clecoed in place
Bottom Side Gusset, riveted in place
Top and Botom Side Gussets, riveted in place
Bottom Gusset, clecoed in place.
Rivet all six gussets in place.

Now we will work on attaching the 'sun roof skin' to the top of the cabin.

The front vertical pieces are marked and cut off with a dremel tool.
After cutting off the vertical angle aluminum supports, we can add in the two cross tube supports, which were are cut from 1" 6061T6 .063 square tubing.

6061T6 1 x 1 x .063 cross bars.  Cut to length shown.

We will also add in the 1" thinwall tubing, which runs along the top of top door skin, and is shown clecoed in and clamped in place in the following photo.   They are simply cut to fit.

All top cabin tubing shown
Top skin clecoed in place.
Another view of top skin clecoed in place.
Small inside gussets for top of cabin.
Riveting the top sunroof skin in place.
Closeup of corner of top skin.
You'll need to make a bend in the windshield support.

Windshield support with bend.
Windshield support clecoed in.
Windshield support riveted in.
Now it's time to cleco in the remaining baggage compartment dividers.

Pay attention:  the tabs may be bent either way, but only one way is correct.  Study the parts, your assembly to date, and all of the photos to ensure that you do it correctly.  The tabs are easily bent in any brake or even with a bench vise.  There are also hand tools which make them easy.

Baggage compartment divider.

Baggage compartment dividers in place.
Note that the bottom skin is not entirely pre-drilled.  This allows you to fit the best alignment on your baggage divider skins and under the front floor pan (which may require you to drill out a few rivets to fit under).

Bottom skin, ready to install.

 Bottom skin clecoed in place, fit under floor pan and under landing gear gusset.

Bottom skin partially riveted in place.
Rear Landing Gear gussets clecoed in place.
Fabric trim plate for bottom landing gear cross attach post.
Fabric trim plate riveted in place.
Front Diagonal Support gusset, bent and riveted in place.
Front Diagonal Support gusset, riveted in place.
Doublers at engine mount area
Doublers at engine mount area, riveted in place.

Top of cabin, ready to accept gusset.
Bent gusset.
Gusset riveted in place.  One of these rivets will be drilled out.
 One of the rivets will be drilled out in order to accept the "X" steel cross brace.

NEXT:  PHOTO REVIEW OF THE CABIN ASSEMBLY, PRIOR TO COVERING.

Belite Aluminum Ultralight Aircraft Cabin Construction, #5

Please note: James' blog has moved to a Wordpress site. To access it, please visit http://jameswiebe.wordpress.com/. All posts have been transferred to the new site, and all new posts will only be accessible via Wordpress. Thank you for your interest!



This post is #5 in a series of articles on how to assemble a Belite Ultralight Aircraft cabin using aluminum.

Post #4 in this series is HERE.
Post #3 in this series is HERE.
Post #2 in this series is HERE.
Post #1 in this series is HERE.

Let's jump right in...  It's looking more and more like a real airplane cabin all the time.

After deburring the top rear skin, clamp it in place:

Clamp the top rear skin in place.

Another view of clamped top rear skin.
Then proceed to clecos and riveting the skin in place.

Rear skin attached with rivets.

Rear skin fully attached with rivets.
If you haven't already, install remainder of rivets along each top side of cabin.  Please note and install extra rivets as shown in photo below.

Side rivets with extra rivets.
Now it's time to add the top side door skins.  Note how they UNDERLAP the star joint on each side.  Also note the windshield attachment piece in the following photo, it will be used a little later in the process.

Side skin and windshield attach piece.

Lucky poses.

Front of side skin, with star joint underlapping clearly visible.

Alignment of side skin, viewed from front.

Rear view.  If all is done perfectly, the rear  corner has a nice sharp corner.

Another view of side skin.

Star joint area.

Yet another view.
It's finally time to fully rivet the star joint.

Finally time to fully rivet the Star Joint!

Done for this afternoon...  more soon.

Monday, December 31, 2012

Teal Beauty Develops on New Years Eve

Please note: James' blog has moved to a Wordpress site. To access it, please visit http://jameswiebe.wordpress.com/. All posts have been transferred to the new site, and all new posts will only be accessible via Wordpress. Thank you for your interest!


Teal Beauty with big wheels.

New Year's Eve.

Hey, we worked today.

The boys and I went home early at 2:00...

Beauty emerges in a Teal color.

By the way, I'm not given away the big tires.  But they sure look sweet on Teal Beauty.



Aluminum Ultralight Aircraft from Belite, under construction

Tail of aluminum ultralight aircraft

Cabin of ultralight aircraft from Belite

Fuel deck on ultralight aircraft from Belite

Firewall goes here

And here is the view from the rear on an ultralight airplane from Belite

Quartering rear view, including tundra tires from Belite Aircraft
Everything you see weighed 86 pounds.  This plane easily makes FAR part 103 ultralight weight, even with the tundra tires.  But we'lll ship it with smaller tires....